Contactless Card Standards – Differences between ISO/IEC 10536, 14443, and 15693

To date, three contactless technologies have received standards classification from the International Organization for Standards (ISO), an umbrella organization made up of 130 national standards bodies from around the world, and the International Electro Technical Committee (IEC), an organization representing more than 50 national standards bodies focused on electronics.

These three standard contactless technologies, as defined by ISO/IEC, are:

  1. ISO/IEC 10536 Close Coupling Cards
  2. ISO/IEC 14443 Proximity Cards
  3. ISO/IEC 15693 Vicinity Cards

Though the official name includes both ISO and IEC, in practice the terms are often shortened to just use the ISO abbreviation (e.g. ISO 14443). In the following paragraphs, we will review each of the three standards from both a technical and a market perspective.

ISO/IEC 10536 – Close Coupling Cards

The ISO/IEC 10536, the close coupling card technology standard, was the first contactless standard to emerge. Cards meeting this standard must be either inserted into a reader or placed upon the surface of the reader for communication to occur. The cards have an extremely short reading distance and require accurate placement of the card of the card at the reader–both major drawbacks for a contactless technology. While ISO 10536 cards were deployed in a number of early projects, the cards are virtually unused today. And with no known supplier for integrated circuit chips for ISO 10536 technology, the standard is, in essence, dead.

ISO/IEC 14443 – Proximity Cards

The ISO/IEC 14443 proximity card technology (ISO 14443) has been used for the overwhelming majority of contactless card deployments worldwide. The targeted range of operations for ISO 14443 cards is up to 10 cm, although this range varies, depending on power requirements, memory size, CPU, and co-processor.

The ISO 14443 standard document has four distinct parts:

  • Part 1: Physical Characteristics
    The card is the ID-1 size (85.6 mm x 54.0 mm x .76 mm). This is the same size as a bank credit card.
  • Part 2: Radio Frequency
    Power and Signal Interface This sections outlines the key technical characteristics of the contactless chip, including items such as frequency, data rate, modulation, and bit coding procedures. Two variations are detailed in Part 2, the Type A interface and the Type B interface. Both operate at the same frequency and use the same data rate, but they differ from one and other in the areas of modulation and bit coding (See Figure 1).
  • Part 3: Initialization and Anticollision
    Initialization describes the requirements for the reader and card to establish communication when the card is brought into the reader’s radio frequency (RF) field. Anticollision defines what happens when multiple cards enter the magnetic field at the same time, identifying how the system determines which card to use in the transaction and ensuring that all cards presented are inventoried and processed.
  • Part 4: Transmission Protocols Transmission protocols define the data format and data elements that enable communication during a transaction.

For a system to comply with ISO 14443, it must meet the requirements of all four parts. Thus, the phrase “ISO 14443, Parts 1 through 4 compliant” is often seen in product descriptions.

ISO/IEC 15693 – Vicinity Cards

The ISO/IEC 15693 vicinity card technology (ISO 15693) developed in response to the industry’s desire for a contactless card technology with an operational range greater than 10 cm. The vicinity card has three modes of operation: read mode, authenticate mode, and write mode. The maximum stated ranges are for read mode, 70 cm, for authenticate mode, 50 cm, and for write mode, 35 cm.

The ISO 15693 standard has three distinct parts:

  • Part 1: Physical Characteristics
    The card is the ID-1 size (85.6 mm x 54.0 mm x .76 mm). This is the same size as a bank credit card.
  • Part 2: Air Interface and Initialization
    Figure 2 summarizes the frequency, modulation, data coding, and data rate values for both reader-to-card and card-to-reader communication as defined in this part of the standard.
  • Part 3: Anti-collision and Transmission Protocol
    Part 3 describes the protocol, command set, and other parameters required to initialize communication between a reader and a card. It also defines the anti-collision parameters, which facilitate the selection of a single card when multiple cards enter the reader’s magnetic field.

Nonstandard Contactless Technologies

A number of proprietary contactless interfaces are used in the industry in addition to the standardized contactless techniques described previously. Two common technologies are Cubic’s GO-Card and Sony’s FeliCa card.

Both of these proprietary technologies are variations on ISO 14443 but each uses a nonstandard bit rate and/or bit encoding method. Attempts by Cubic and Sony to receive standards classification for these products under ISO 14443 were unsuccessful.

In essence, the goal of the manufacturers was to add the proprietary interface types to Part 2 of the 14443 standard as Type C or Type D varieties. In response to the request, Working Group 8 determined that they would not add additional interface types to the 14443 standard.

Card Readers

With multiple card standards in place, the selection of a card reader has greater significance for a program’s long-term flexibility. Well over one million contactless card readers have been deployed to date.

The current deployment trend favors readers that will accommodate several different card types. An example of this flexibility is the emergence of readers that support ISO 14443 Type A and Type B, ISO 15693, and even an additional proprietary card type.

Leave a Reply

Your email address will not be published. Required fields are marked *

Special Offer for Hackers!Sign up to get your $5 Coupon code and weekly deals straight to your inbox!
X